AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Blackfire crystal seal paint sealant9/7/2023 It went on very easily and was very user friendly. Overall, I really, really like this product. In the end, I only had two spots that I needed to quickly swipe with a MF. I ended up doing 3 passes on every panel just to get all of it rubbed up (plus it satisfied my OCD). I did feel like it needed another spray, but I went against what I wanted to do just based on the directions. This got 90% of it rubbed in, so I went back and forth again to get the rest. I went back and forth and then up and down. It spread very easily and I was able to tell when the pad got too dry when I heard the terrible squeaking sound the pad makes on dry paint. I started on the roof and did one spray directly into the middle. Directions advised to spray directly on the paint and go from there. I know they really stressed using very little product, so I didn't use very much. I applied the sealant using the LC foam applicator pad. I was going to use the Blackfire Paint Cleaner as recommended but I had some 70% IPA on hand, so I diluted it down and wiped all of the paint down. I used the WW to remove any stubborn polish.Ĥ. I used a white LC paid and polished the paint. I had some very minor swirls that could be removed with the 205. I used my swirl light and checked the paint all around. Once it was all sudded up, I scrubbed it down with my mild clay towel and rinsed.ģ. I washed the car the old fashioned way with my MF wash mitt and shampoo.Ģ. It was going to be entered in Focus Fest 2015 a few days after the application, so it sounded like a perfect time to test!ġ. I tested this on my tuxedo black 2014 Focus ST. Prior to the coating being applied, there was a coat of Meguiar's M21 topped with Collinite 845 that needed to be removed. Once completed, I kept it indoors for a couple of days to cure. I applied the coating indoors at 72 degrees. Then mist each panel once and spread Crystal Seal evenly in straight line motions.Ĥ.Use this same method to apply Crystal Seal to paint, glass, metals, and hard plastics. Always use a clean, soft applicator to spread Crystal Seal over your vehicle.Ģ.Mist the applicator once to prime it. Hyper-concentrated BLACKFIRE Crystal Seal packs the power of cross-linking Wet Diamond polymers in every drop.ġ.Use very little BLACKFIRE Crystal Seal. Just drops of this clear liquid produces a tough barrier over auto surfaces that resists contamination, moisture, and UV rays. If isolated streaking is visible in some areas after 60 minutes lightly wipe with a Corba microfiber towel to remove.BLACKFIRE Crystal Seal is a paint sealant coating that offers incredible protection and longevity for all paint finishes, plastics, glass, and metals. Try to keep the vehicle out of the elements for the next 8 hours to allow the Wet Diamond Polymers to fully cross-link.īLACKFIRE Crystal Seal is excellent when applied to brake calipers & wheels, door jambs, interior trim (such as carbon fiber), metal trim, and windows. Wait 30-60 minutes for all high-spots to level and cure. Very little goes a long way, 4 ounces can treat up to 40 vehicles.Īpply to the next section until the entire vehicle is covered. a fender, half the hood, a door, and spread using straight lines until a thin even coat is applied. Mist BLACKFIRE Crystal Seal onto the microfiber applicator pad to prime it. Machine polish paint defects if necessary or use BLACKFIRE Gloss Enhancing Polish to clean and prepare the paint. For maximum effect apply BLACKFIRE Crystal Seal to prepared paint or existing BLACKFIRE protection. Crystal Seal is will not stain plastic and trim.īLACKFIRE Crystal Seal contains no cleaning agents. Crystal Seal is a unique self-leveling formula that does not require additional buffing or removal. Each spray BLACKFIRE Crystal Seal contains enough Wet Diamond Polymers to protect your paint and create that unmistakable BLACKFIRE Shine.
0 Comments
Read More
Leave a Reply. |